Part no.: 77 3405 0000 23003-0200
M8 Male cable connector, Contacts: 3, unshielded, moulded on the cable, IP67, Standard, PVC, yellow, 3 x AWG 22, 2 m
Connecting Cables, series 718, Automation Technology - Sensors and Actuators
General features
Moreless| Part no. | 77 3405 0000 23003-0200 |
| Connector design | Male cable connector |
| Cable length | 2 m (Standard 2 m and 5 m. Other lengths are available on request.) |
| Connector locking system | screw |
| Termination | moulded on the cable |
| Degree of protection | IP67 |
| Connection cross-section | 0.34 mm² / AWG 22 |
| Temperature range from/to | -25 °C / 85 °C |
| Mechanical operation | > 100 Mating cycles |
| Weight (g) | 109 |
Electrical parameters
Moreless| Rated voltage | 50 V (AC) / 60 V (DC) |
| Rated impulse voltage | 1500 V |
| Rated current | 4.0 A |
| Pollution degree | 3 |
| Overvoltage category | II |
| Insulating material group | II |
| EMC compliance | unshielded |
Material
Moreless| Housing material | PUR |
| Contact body material | PUR |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Locking material | Zinc die-cast nickel-plated |
| REACH SVHC |
CAS 7439-92-1 (Lead) |
| SCIP number | SCIP-number not available |
Cable data
Moreless| Structure of the cable | |
| Cable type | Standard |
| Cable diameter | 4.7 mm |
| Cross section | 3 x AWG 22 |
| Sheath material | PVC |
| Single-lead structure | 26 x 0,36 mm |
| Cable color | yellow |
| Electrical properties | |
| Cable Insulation resistance | 60.0 Ω/Km (20 °C) |
| Operating voltage | 300 V |
| Cable test voltage | 2000 V |
| Conductor resistance | 60 Ω/Km (20°C) |
| Mechanical properties | |
| Bending radius, fixed cable | min. 10 x Ø |
| Bending radius, moving cable | min. 5 x Ø |
| Bending cycles | 10 million |
| Travel distance, horizontal | ≥ 5 m |
| Travel distance, vertical | ≥ 5 m |
| Thermal properties | |
| Temperature range cable in move from/to | -25 °C / 105 °C |
| Temperature range cable fixed from/to | -50 °C / 105 °C |
| Other features | |
| Halogen free | no |
General Disclaim Notice
- The connector must not be plugged or unplugged under load. Non-observance and improper use can result in personal injury.
- The connectors have been developed for applications in plant engineering, control and electrical equipment construction. The user is responsible for checking whether the connectors can also be used in other areas of application.
- To protect against unintentional opening of the connector, the thread between the housing and the connector head must be secured with a suitable cyanoacrylate adhesive when used in circuits with voltages dangerous to the touch. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors which are used in circuits with voltages dangerous to the touch may only be installed and used by, or under the supervision of, persons with electrical engineering training, taking into account the applicable regulations and standards.
- The user must take suitable safety precautions to ensure that the connector cannot be accidentally disconnected.
- Plug connectors with enclosure protection IP67 and IP68 are not suitable for use under water. When used outdoors, the plug connectors must be protected separately against corrosion. For further information on the IP protection classes, please refer to the "Technical Information" download centre.
- Please observe the pollution degree and the overvoltage category. For further information, please refer to the download center "Technical Information".
- To lock the cable connector with the device connector, the threaded ring is tightened "hand-tight" (approx. 40 cNm).
